4th International Conference on Material Engineering and Application (4th ICMEA 2019)

Selected, peer reviewed papers from the 4th International Conference on Material Engineering and Application (4th ICMEA 2019), August 23-25, 2019, Kuala Lumpur, Malaysia

• Preface
• Chapter 1: Engineering Materials
• Effect of Plating Thickness on Fatigue Strength of Galvanized Steel
• Influence of Nano-Silica Dosage on Properties of Cement Paste Incorporating with High Calcium Fly Ash
• Mechanical and Shrinkage Behaviors of Ductile Fiber-Reinforced Polymer Repair Mortar
• Development of a TAPE-Agar Liquid Gel Bandage
• Frequent Start-Stop Test Study of Graphene Coatings on Journal Bearings
• A New Technology to Prevent the Formation of Limescale in Hot Water Supply Systems
• Development of a CuFe₂O₄ - Reduced Graphene Oxide-Based Electrochemical Sensor for Malathion
• Nano-Crystallization of Steel Surface by Slide-Burnishing
• Numerical Simulation of Material Plastic Deformation Using the Drawing Forming Process of Contoured Internal Surface Tubes
• Solvent Absorption and Dissolution Kinetics Modelling for the Chemical Recycling of Waste Plastic Laminates
• Feasibility of Paper Production from Oil Palm Trunk Using Arrowroot Flour as a Binder
• Study on Morphology Features and Mechanical Properties of Nanofibers Films Prepared by Different Composite Electrospinning Methods
• Studying the Stability and Conductivity of the Composite Films via Electrospinning/Spray Process
• Electrospinning/Spray: The Interaction between Graphene Nanosheets and Different Nanofibers
• Tensile Properties of Cellulose-Filled Recycled Thermoplastic Composite Filaments for 3D Printing
• 3D Reconstruction of Microstructure for Centrifugal Casting Babbitt Lining of Bimetallic Bearing Based on Mimics
• X-Ray Powder Diffraction Data and Crystal Refinement of Ternary Compound Ti₄ZrSi₃
• The Green Preparation of Cellulose Fibrils from Oil Palm Leaf Stalk Fibers for Hydrogel Applications
• Evaluation of Recycled Aggregate (RAP) Presence Impact under Indirect Tensile Strength of Bitumen Stabilized Mix with Foamed Asphalt for a Base Layer
• Scanning Electron Microscope in Rocks and their Comparison with Physical-Mechanical Properties
• Natural Additive to Retard the Setting of a Mortar and Increase its Resistance
• Electrochemical Synthesis of Hydroxyapatite Nanosheet-Assembled Porous Structures with Bipolar Membrane
• The Comparison between Mechanical Properties of Laser-Welded Ultra-High-Strength Austenitic and Martensitic Steels
• Mechanical Properties of Concrete Using Treated Recycled Concrete Aggregate in Marine Environment
• Failure Analysis of Spur Gears Used in Transmission System Applied on a Hand Tractor
• Biofuel Production from Jatropha Bio-Oil Derived Fast Pyrolysis: Effect of Catalysts Supported
• Experimental Investigation and Modelling of Claystone from Mae Moh Coal Mine, Thailand
• Preliminary Investigation of Crushed Rock-Based Geopolymer for Road Applications
• Hemp Fiber Reinforced Geopolymer Composites: Effects of NaOH Concentration on Fiber Pre-Treatment Process
• Crushed Rock Geopolymer as a Future Road Construction Material: An Evaluation on Strength Performance and Compaction Characteristics
• Response Behavior of Local Surface Failure due to Repetitive Impact of Stainless Steel
• Study of Properties of 3D Printed Short Carbon Fiber Composite
• High Purity Lime as an Ecologic Alternative for Construction Mortars and Pastes
• Cemented Mortar Matrices Densified with Organic Additions
• Evaluation of the Electrical Resistivity, Ultrasonic Pulse Velocity and Mechanical Properties in Portland Cement Pastes Type II
• Characterization of Hydraulic Concrete with Polystyrene-Based Emulsion
• Preparation and Performance Study of Fluorosilicone Oligomer Anti-Sticking Coatings
• The Effect of Alloying on the Fractional Composition, Shape and Grain Size Distribution of the Structure Alloy GAP the Fe-Nd-B System
• Optimization of Methylene Blue Adsorption via Functionalized Activated Carbon Using Response Surface Methodology with Central Composite Design
• Rejection Rate Reduction of the Automotive Thermoplastic Parts in Injection Moulding Using Response Surface Methodology
• Simulation of Gap Flow Field in EDM Process Uesd Oil-in-Water Working Fluid
• Synthesis, Preparation and Characterization of Amine-Induced Bacterial Cellulose-Poly(Vinyl Alcohol) Semi-Interpenetrating Network Hydrogel
• Effect of Substrate Temperature on the Electronic Properties of MgO Thin Films on Si (100) Grown by Electron Beam Evaporation
• Button of Hydroxyapatite Composite for Craniotomy Flap Fixation: Fabrication and Mechanical Properties
• Analysis of Physical and Mechanical Properties of Backhoe’s Bucket Repairment with Cladding Methode
• Fabrication Study of Cu-C-Ni for EDM Electrode by a Sintering Technique
• Synthesis and Characterization of Active Biocarbon Material for Use in Cosmetics and Personal Care Products
• Characterization of Adsorbents Derived from Palm Fiber Waste and its Potential on Methylene Blue Adsorption
• Potential Activity Evaluation of Phosphorus on CoMo/Al₂O₃-TiO₂ Catalysts to Co-Processing Model
• Investigation of the Tensile and Flexural Behavior of Polylactic Acid Based Jute Fiber Bio Composite
• Fatigue and Fracture Mechanism of Aluminum-Carbon Fiber Reinforced Hybrid Composites
• Fatigue-Corrosion of High Strength Steels in Synthetic Seawater under Cathodic Protection
• Effect of Cr and Si Contents on the Magnetic and Mechanical Properties of Fe-Cr-Si Alloys by MIM Process
• Microstructure and Mechanical Properties of Laser Welded 316L SLM Parts
• The Effect of Calcination Temperature on Metakaolin Characteristic Synthesized from Badau Belitung Kaolin
• Flavor Quality Changes of Turbot (Psetta maxima) Stored at -2 and 0°C
• Investigation on Mechanical Behavior of Sisal Fiber Reinforced Polylactic Acid and Sisal/Epoxy Composites
• Evaluation of Mechanical Properties of Sugarcane Reinforced Hybrid Natural Fibre Composites by Conventional Fabrication and Finite Element Method
• Study of Deep Cryogenic Treatment Process Effect on Microstructure and Properties of CuBeZr Alloy
• Casting of High Aluminum Content AM Series Magnesium Alloys by Using a Horizontal Twin Roll Caster
• Estimation of Cold Roll Forming Characteristics of Wrought Magnesium Alloy with Tension-Compression Asymmetry
• Chapter 2: Materials Properties and Application
• Analogy of Non-Destructive Tests for the Detection of Defectologies in Aluminium Cylinder Heads
• Surface Roughness Prediction Based on Acoustic Emission Signals in High-Precision Diamond Turning of Rapidly Solidified Optical Aluminum Grade (RSA443)
• Flow Field Analysis and Experimental Investigation of Electrochemical Etching
• 3D FEM Study of the Flow Uniformity of Flat Polypropylene Film/Sheet Extrusion Dies
• Prediction of the Fatigue Life of the SAE 5160 Carbon Steel Coil Spring Based on Strain-Life Approach
• Design and Optimization of Die Body for Polymer Extrusion