This book presents the latest research results in materials science, engineering science, and technology which were introduced at the 5th EPI International Conference on Science and Engineering 2021, Indonesia. The edition will be interesting and useful to researchers and engineers from materials science, microelectronics, mechanical engineering, civil engineering and architecture.

Les mer
<p>Selected peer-reviewed extended articles based on abstracts presented at the 5th EPI International Conference on Science and Engineering (EICSE2021)</p> <p>Aggregated Book</p>
  • Preface
  • Chapter 1: Properties and Processing of Steel and Alloys
  • Mechanical Properties Comparison Between Induction Hardening and Rehardening of Axle Shaft AISI 1043 According to JIS G 0559 Standard
  • Strength Analysis of ST 41 Steel as Propeller Shaft with Quenching Heat Treatment and Tempering after Carburizing Carbon Media Variations
  • Experimental Investigation on the Effect of EDM Wire Cut Parameters on the Formation of Cr23C6 in AISI 316 Steel
  • Analysis of Voltage, Current Density, and Welding Speed of Flux Core Arc Welding on the Hardness and Micro-Structure of High Strength Low Alloy (ASTM A572)
  • The Influence of Machining Variables on the Quality of the Shaping Process on Hard Steel
  • Chapter 2: Composite Materials and Structures
  • Crashworthiness Analysis of Vehicle Crash-Box Filled with Aluminium Foam
  • Improving Fiber-Matrix Compatibility by Surface Modification of Coconut Coir Fiber Using White Rot Fungi
  • Ramie Fiber Woven Composite: The Effect of Feedrate Variation on the Tensile Strength of the Open Hole in the Drilling
  • Mathematical Model of Shear Stress Transfer at Fiber-Matrix Interface of Composite Material
  • Study on the Mechanical Properties and Behavior of Corrugated Cardboard under Tensile and Compression Loads
  • Chapter 3: Materials and Processing Technologies in Photovoltaics and Mechatronics
  • Conductive Glass with Simple Spray Deposition Method for Dye-Sensitized Solar Cell Application
  • Semiconductor TiO2 Coating Deposited by Microwave Plasma Method
  • Fabrication of Chemotaxis Microfluidic Device Mould Using Digital Light Processing 3D Printing Method
  • Chapter 4: Materials in Construction
  • Shear Strength Analysis of Rock due to the Effect of Surface Roughness Based on Laboratory Testing and Numerical Modeling
  • External Shear Strengthening of RC Beams with Anchored Geopolymer Fiber Mortar Panel: An Experimental Study
  • Failure Mode of GFRP Bar RC Beams Using GFRP Sheet as Shear Reinforcement
  • Strength Development of Seawater Mixed and Cured Concrete with Various Replacement Ratios of Fly Ash
  • Study on some Properties of Sustainable Mortar Incorporating Processed Waste Tea Ash
  • Investigation of Depth Variations of the Bamboo Twigs for its Acoustical Performance
  • The Sound Absorption Characteristics of Bamboo Twigs Based on Surface Combination Patterns
  • The Utilization of Geopolymer Mortar as Permanent Formwork in Reinforced Concrete Beam
  • Assessment of Stone Ash as a Fine Aggregate Material to Meet the Value of Normal Concrete Compressive Strength
  • Sound Absorption Coefficient Analysis for Composite Made of Agricultural Waste
  • Chapter 5: Structural Mechanics
  • Analytical and Experimental Study for Vibration of Laminated Rectangular Plates with Point Masses
  • Accurate Results by the Ritz Method for Free Vibration of Uniform Annular Plates
  • The Critical Load on Quadrilateral and Circular Hollow Pipes under Pure Bending and Pure Torsion
  • Laboratory Testing and Numerical Analysis on Reinforced Concrete Frames with Prefabricated Cellular Lightweight Concrete (CLC)
  • A Study of Alternative Materials for Sail Mast of Sandeq
Les mer

Produktdetaljer

ISBN
9783035727722
Publisert
2023-07-28
Utgiver
Vendor
Trans Tech Publications Ltd
Vekt
630 gr
Høyde
240 mm
Bredde
170 mm
Dybde
14 mm
Aldersnivå
P, 06
Språk
Product language
Engelsk
Format
Product format
Heftet
Antall sider
288

Redaktør